AirsoftGuns s.r.o.
Processor unit, V.2, JeffTron
Microprocessor-controlled MOS FET with active brake designed for electric airsoft weapons from JeffTron. Adds new ways of firing, infinitely variable rate of fire weapon, active motor braking and low battery indication. Fully integrated devices are installed inside the gearbox v. 2 instead of the original trigger contacts according to the company standard Tokyo Marui.
Microprocessor-controlled MOS FET with active brake designed for electric airsoft guns from JeffTron. Adds new ways of firing, infinitely variable rate of fire weapon, active motor braking and low battery indication. Fully integrated devices are installed inside the gearbox v. 2 instead of the original trigger contacts according to the company standard Tokyo Marui.
The barrel parameters:
- Easy to install inside the gearbox v. 2
- Preserving the function of the mechanical shutter stops for secured weapons (SAFE mode)
- Six new shooting modes, shooting adjustable dose (optional in the range of 1-10 gears)
- The continuous change of rate of fire using lossless PWM control
- Quick first shot at a reduced rate of fire
- Switching the motor using MOS FET with active braking (can be adjusted or even turned off)
- Battery low for 2S and 3S Li-Po, 3S li-fe, 3S li-on
- Babysitting passing current,Voltage and temperature components
- Programming the device is done via a trigger, which uses the vibration of the motor in reverse pistol grip
- Changing the settings, so you do not lose programming after disconnecting the battery
Selecting shooting modes:
- Safe - Single - Auto (function unchanged weapons)
- Safe - Single - Burst/Auto
- Safe - Single - Single
- Safe - Single - Burst
- Safe - Single - Single (forced timeout for another shot, motor vibration indication)
- Safe - Burst - Burst/Auto
- Safe - Single/Burst - Burst/Auto (unique shooting mode only integrated procesored)
Specifications:
- Only for electric airsoft weapons with a standard gearbox version 2 switches according to the original concept proposed by Tokyo Marui
- Stand-alone devices without cables, for power circuit cables can be used for max. 1.5 mm for signal and a cross section of 0.25 mm2
- Designed for M160 springs into 25 balls and rate of fire/s, but it always depends on a good configuration of other components in the assembly
- For proper function of this ECU it is necessary to have a functional Gearbox interrupter switches backdrop, reverse latch, trigger a mechanical shutter to ensure
- Designed for all types of co mmonly used batteries up to 12V (Ni-xx 8.4 - 12V Li-Pol 7.4 - 11.1V)
- Current consumption forces only 4.5 mA in idle mode
- Contactless switching motor
- Devices enhances rate of fire weapon and battery life than the original wiring in weapons
WARNING: The installation of this equipment is needed expert who must know how to solder and spread AEG gun. For most co mmercially available and can be extended brands installed without major modifications.
The barrel parameters:
- Easy to install inside the gearbox v. 2
- Preserving the function of the mechanical shutter stops for secured weapons (SAFE mode)
- Six new shooting modes, shooting adjustable dose (optional in the range of 1-10 gears)
- The continuous change of rate of fire using lossless PWM control
- Quick first shot at a reduced rate of fire
- Switching the motor using MOS FET with active braking (can be adjusted or even turned off)
- Battery low for 2S and 3S Li-Po, 3S li-fe, 3S li-on
- Babysitting passing current,Voltage and temperature components
- Programming the device is done via a trigger, which uses the vibration of the motor in reverse pistol grip
- Changing the settings, so you do not lose programming after disconnecting the battery
Selecting shooting modes:
- Safe - Single - Auto (function unchanged weapons)
- Safe - Single - Burst/Auto
- Safe - Single - Single
- Safe - Single - Burst
- Safe - Single - Single (forced timeout for another shot, motor vibration indication)
- Safe - Burst - Burst/Auto
- Safe - Single/Burst - Burst/Auto (unique shooting mode only integrated procesored)
Specifications:
- Only for electric airsoft weapons with a standard gearbox version 2 switches according to the original concept proposed by Tokyo Marui
- Stand-alone devices without cables, for power circuit cables can be used for max. 1.5 mm for signal and a cross section of 0.25 mm2
- Designed for M160 springs into 25 balls and rate of fire/s, but it always depends on a good configuration of other components in the assembly
- For proper function of this ECU it is necessary to have a functional Gearbox interrupter switches backdrop, reverse latch, trigger a mechanical shutter to ensure
- Designed for all types of co mmonly used batteries up to 12V (Ni-xx 8.4 - 12V Li-Pol 7.4 - 11.1V)
- Current consumption forces only 4.5 mA in idle mode
- Contactless switching motor
- Devices enhances rate of fire weapon and battery life than the original wiring in weapons
WARNING: The installation of this equipment is needed expert who must know how to solder and spread AEG gun. For most co mmercially available and can be extended brands installed without major modifications.
