Processor unit, PSJ-M3 gen.3, universal wires, GRIZZLYNew generation of PSJ processor unit from Grizzly for AEG weapons with a mechabox version III. brings many new functions and easier installation. All the great function of previous generations are kept - contactless magnetic switching, powerful MOSFET cooled via the whole gearbox, active brake fully functional in any mode, programmable burst and so on. On top of that the active brake is now adjustable up to completely disabled, we’ve added advanced rate of fire settings, energy consumption is now as low as 3.9mA and there are many more new features and updates.
• simplified unit installation
• simplified magnet installation – polarity doesn’t affect functionality
• lower energy consumption, as low as 3.9mA
• can be used with spring up to M200 with rate of fire 99rpm
• longer wires, suitable for all replica types
• adjustable rate of fire
• adjustable active brake with possibility to be completely disabled
• compatible with batteries up to 4S / 16.8V
• a screw added to accessories to attach the unit into the gearbox
• new, thicker insulation foil preventing short circuit
• possible usage of dual sector gears
• layered varnish coating preventing short circuit
• new service connector
• 6 pre-set fire modes
• automatically switches from Burst to full auto when trigger pulled for longer time, without any delay
• modes are fully programmable by the trigger
• configurable Burst mode - from 1 up to 255 BBs shot on one quick trigger pull, this setting works in all modes containing Burst
Rate of fire:
• allows you to set delay between the two following shots
• allows smooth rate of fire setting
• programmable by trigger
• default settings reset: You can simply reset all settings to their default values by trigger
• manual mode: If your PSJ indicates damage and you are sure it is not mechanical and your replica is able to shoot, you can access manual mode in which malfunction is ignored. You can then fire on full auto mode only
(WARNING! By poor judgement, you can cause more damage to your replica and the unit!)
• no mechanical switch, switching is contactless
• faster trigger response
• increased rate of fire and battery life
• maximum current up to 202A constant and 808A in peek
• stops motor immediately with piston in default position and spring loose (when 100% set)
• increases lifetime of piston, spring and many other parts
• always finishes whole rotation of gear wheels
• fully functional in all fire modes
• adjustable by steps of 10%
• possibility to completely disable active brake (set 0%)
• unit detects mechanical damage and disables shooting to prevent any other damage
• user is warned by motor vibrations
Li-Pol/Li-Ion/Li-Fe battery check:
• when lithium battery is discharged, unit warns user by motor vibrations
• battery type needs to be set – easily done using trigger itself
• warning is off for Ni-MH, Ni-Cd batteries
Realistic trigger operation:
• trigger sensitivity can be set during installation to best fit your demands (see instructions at www.grizzlyairsoft.com)
• solves problem with double shot on semi
• anti-reversal latch may not be needed if the motor is powerful enough (not recommended)
All this hidden inside your gearbox:
• the whole unit is installed inside your gearbox, replacing trigger contacts
• only two power wires come from gearbox
• unit is equipped with LED indication of correct installation for easier installation
• Generation 3 units are suitable for AEG replicas according to the version of gearbox each unit is designed for. Units have been tested in gearboxes of following manufacturers*: AimTop, APS, ARES, ASG Ultimate, Cyma, DBoys, Guarder, RetroArms, SHS, SRC
*Every manufacturer innovates their products over the time, so there is possibility, that the gearbox tested by us is different from yours. However this only means, that your installation might require some minor adjustments.
• Top quality silicone wiring. 1mm2 in cut capable of transmitting up to 47A constant.
• Powerful MOSFET with maximum current up to 202A constant and 808A in peak allows use almost without any restrictions.
• MOSFET is effectively cooled by the whole gearbox.
• The whole unit is coated in multiple layers of varnish for maximum durability even in poor conditions.
• Replica‘s rate of fire is limited by gearbox components and technical specifications. PSJ unit itself is able to do up to 500 000 cycles (shots) per second. Unit is tested for 99 cycles (shots) per second.
• Current consumption of unit in standby mode is as low as 3.9mA.
• processor unit PSJ gen.3
• complete silicone wiring of your choice
• pre-installed insulation foil
• heat conducting foil
• magnets for the trigger and the cut-off lever
• modified selector plate with magnet installed
• dean-T plug – male
• gold-plated motor plugs – 2pcs
• gold-plated fuse plugs – 2pcs
• fuse mini
• heat shrink tubing
• user and installation manual
WARNING: PSJ should be installed by qualified AEG professionals only! Manufacturer is not liable for any damage on the replica caused by unprofessional installation. Do not use soldering gun!